From large polycyclic aromatic hydrocarbons to extended aromate-rich networks

The common ground of this study is the development of novel synthetic strategies to extended one-, two- and three-dimensional aromate-rich systems for which a number of applications are envisaged. rnThe point of departure is the synthesis and characterization of highly symmetric macrocyclic PAHs (polycyclic aromatic hydrocarbons) for which various aspects of supramolecular chemistry will be investigated. The versatility of the Yamamoto macrocyclization will be demonstrated on the basis of a set of cyclic trimers that exhibit a rich supramolecular chemistry. 1,10-phenanthroline, triphenylene and ortho-terphenyl building blocks have been successfully assembled to the corresponding macrocycles following the newly developed synthetic route. Scanning-tunneling microscopy (STM) and two-dimensional wide-angle X-ray scattering (2D-WAXS) were used to study the two- and three-dimensional self-assembly, respectively.rnSecondly, the development of chemical approaches to highly shape-anisotropic graphene nanoribbons (GNRs) and related nanographene molecules shall be discussed. Aryl-aryl coupling was used for the bottom-up fabrication of dendronized monomers, polymers and model compounds. Subsequently, these structures were converted into the final graphene material using oxidative (Scholl-type) cyclodehydrogenation. The GNRs thus obtained are characterized by an unprecedented length and lateral extension. The relevance of structural tailoring in the field of well-defined graphene materials is discussed in detail as only the chemical approach provides full geometry control. rnLastly, novel pathways towards the synthesis of extended three-dimensional networks that are dominated by nitrogen-rich motifs will be presented. If porous, these materials hold a great potential in the fields of gas and energy storage as well as for applications in catalysis. Hence, poly(aminal) networks based on melamine as crosslinking unit were synthesized and characterized with respect to the applications mentioned above. As set of conjugated poly(azomethine) networks was investigated regarding their use as a novel class of organic semiconductors for photocatalytic water splitting. The network structures described in this chapter can also be subjected to a controlled pyrolysis yielding mesoporous, nitrogen-rich carbon materials that were evaluated as active component for supercapacitors.rn

HCl gas gettering of 3d transition metals for crystalline silicon solar cell concepts

In order to reduce the costs of crystalline silicon solar cells, low-cost silicon materials like upgraded metallurgical grade (UMG) silicon are investigated for the application in the photovoltaic (PV) industry. Conventional high-purity silicon is made by cost-intensive methods, based on the so-called Siemens process, which uses the reaction to form chlorosilanes and subsequent several distillation steps before the deposition of high-purity silicon on slim high-purity silicon rods. UMG silicon in contrast is gained from metallurgical silicon by a rather inexpensive physicochemical purification (e.g., acid leaching and/or segregation). However, this type of silicon usually contains much higher concentrations of impurities, especially 3d transition metals like Ti, Fe, and Cu. These metals are extremely detrimental in the electrically active part of silicon solar cells, as they form recombination centers for charge carriers in the silicon band gap. This is why simple purification techniques like gettering, which can be applied between or during solar cell process steps, will play an important role for such low-cost silicon materials. Gettering in general describes a process, whereby impurities are moved to a place or turned into a state, where they are less detrimental to the solar cell. Hydrogen chloride (HCl) gas gettering in particular is a promising simple and cheap gettering technique, which is based on the reaction of HCl gas with transition metals to form volatile metal chloride species at high temperatures.rnThe aim of this thesis was to find the optimum process parameters for HCl gas gettering of 3d transition metals in low-cost silicon to improve the cell efficiency of solar cells for two different cell concepts, the standard wafer cell concept and the epitaxial wafer equivalent (EpiWE) cell concept. Whereas the former is based on a wafer which is the electrically active part of the solar cell, the latter uses an electrically inactive low-cost silicon substrate with an active layer of epitaxially grown silicon on top. Low-cost silicon materials with different impurity grades were used for HCl gas gettering experiments with the variation of process parameters like the temperature, the gettering time, and the HCl gas concentration. Subsequently, the multicrystalline silicon neighboring wafers with and without gettering were compared by element analysis techniques like neutron activation analysis (NAA). It was demonstrated that HCl gas gettering is an effective purification technique for silicon wafers, which is able to reduce some 3d transition metal concentrations by over 90%. Solar cells were processed for both concepts which could demonstrate a significant increase of the solar cell efficiency by HCl gas gettering. The efficiency of EpiWE cells could be increased by HCl gas gettering by approximately 25% relative to cells without gettering. First process simulations were performed based on a simple model for HCl gas gettering processes, which could be used to make qualitative predictions.